How BackCountryVans trimmed for tire clearance

Post Reply
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

How BackCountryVans trimmed for tire clearance

Post by loopie »

I went ahead and did this procedure prior to even testing for rub.
2.5" lift and 235's on stock rims is 100% rub free on my '97.
What a trim like this also does is remove any sharp edges that would cut a tire size that slightly rubs :supz:

Blank canvas
Image

Remove the inner splash guard
Image
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

Take a sawzall(or what-have-you) straight thru at this angle and remove the bracket too
Image

Image
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

No change to the cosmetic appearance from outside the wheel well...see? Don't be afraid kids...:)
Image
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

Cut a slice into the lip at the corner. Not completely necassary, but the lip will fold nicer
Image

A 2.5lb sledge makes short work of the fold, but any hammer will get ya there
Image

Now do the verticle lip...pound it all flat and feel for any sharp edges..you want it all smooth
Image
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

Clean it and primer it. In this pic, also note that you may have to trim a little of the rubber splash guard as seen in the right circle, and also use a pair of pliers to fold back/up the thin sheet metal splash guard...easy peasy
Image
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

Trim that inner splash guard you removed earlier
Image

Done! (covered the primer with some truck bed liner)
Zero rub from 235's :)
(pic doesn't show the folding up of that lower edge on the right tho)
Image
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

For the front bumper, I actually cut quite a junk out of it and is certainly way more than necassary...but I like this look better :)
Details to follow.
Image
User avatar

Herbie
ASV Supporter
ASV Supporter
Posts: 674
Joined: Tue Aug 04, 2009 10:45 am
Location: San Diego, CA
Has thanked: 12 times
Been thanked: 4 times
Contact:

Re: How BackCountryVans trimmed for tire clearance

Post by Herbie »

Great shot's loopie! I'm bookmarking this thread for reference in a couple of weeks when I get my own lift put on.

From another thread, your 235's are "235/75 DuraTracs" - your van is a '97, right, so that's a 235/75-15? Just want to be sure, for comparison's sake as my 2003 rides 16" wheels. A 235/75-15 is nominally 28.9, and a 235/75-16 is nominally an inch bigger... I'm not adverse to some trimming but I'm trying to pick tires that definitely WILL NOT rub afterwards.
"My minivan is cooler than your bro-truck"
2003 Astro AWD Astrolander/ZMB - GTRV Top Transplant, 4" OLV Lift, NP233 T-case, evolving interior
1995 Safari GTRV Organ donor - gutted and gone.
Image

astrozam
I have my van tatooed on my cheeks
Posts: 2770
Joined: Fri Sep 08, 2006 2:57 am
Has thanked: 1 time
Been thanked: 2 times

Re: How BackCountryVans trimmed for tire clearance

Post by astrozam »

Nice job loopie, thanks for the write up :supz:
User avatar

doyoulikeithere
ASV Supporter
ASV Supporter
Posts: 2060
Joined: Tue Nov 17, 2009 8:27 pm
Location: Misty Mountains of Cowichan BC.

Re: How BackCountryVans trimmed for tire clearance

Post by doyoulikeithere »

Looks good Loops!
I just did mine a while back too.

Hey, is Backcountryvans a business name?
Are you putting together lift kits etc?
Have you got a good source for new lift leaf springs ?
2021 Yamaha Tenere 700 - Blue.
2016 Yamaha XSR900 - Silver.
1990 Astro - AWD - Brown.
1987 Astro - With 5 Speed & 4wd - Silver & Blue.
User avatar

Topic author
loopie
I finally get the smurf thing
Posts: 215
Joined: Sun Mar 29, 2009 6:04 pm
Location: kamLOOPs, BC, Canada

Re: How BackCountryVans trimmed for tire clearance

Post by loopie »

^yup...just a part time , working off the kitchen table kinda business. I wanted to take a different approach to a few key things and thought I'd take the time to make them available as well. It's gettin' there. Thing is...I've taken on too many "part time" things lately... :muhaha: [-(

Rear springs....Due to shipping costs, I'd like to suggest a local spring builder to everyone...but reputation and skill makes or breaks a good spring. So not everyone has a "good" local spring place. Before searching in depth local to me (for Canadian buyers)...my go-to place would be http://www.eatonsprings.com/ I may work with these guys in the future to drop-ship custom springs made to his/my specs.

Astrophysics
I sleep in my van
Posts: 974
Joined: Sat Jan 12, 2008 9:23 pm
Been thanked: 9 times

Re: How BackCountryVans trimmed for tire clearance

Post by Astrophysics »

Hi Loopie,

Hi Herbie,

Thank you for the great photos.

With the instructions, I finally had the skill and confidence to trim fender cladding on my 2" lifted 2003 $x4 Astro.
I h
Just got the new Cooper Discover AT3 4 S in P245/75-16. On stock aluminum wheels.

They rubbed big time without the trimming.

They still hit the sway bar!

Can I file or grind off some of the sway bar?

The sway bar is thick, about 30 mm OD

AP
Attachments
Inner fender trimming
Inner fender trimming

Astrophysics
I sleep in my van
Posts: 974
Joined: Sat Jan 12, 2008 9:23 pm
Been thanked: 9 times

Re: How BackCountryVans trimmed for tire clearance

Post by Astrophysics »

Howdy,

After trimming, I cleaned metal wire brass brush and citrus degreaser. Let it dry, wiped down with blue shoptowel.
Sprayed with Rustoleum spray rubber black.

Nice.
Attachments
12 volt mini Milwaukee hack saw with pvc blade,  east cut,
12 volt mini Milwaukee hack saw with pvc blade, east cut,

Astrophysics
I sleep in my van
Posts: 974
Joined: Sat Jan 12, 2008 9:23 pm
Been thanked: 9 times

Re: How BackCountryVans trimmed for tire clearance

Post by Astrophysics »

Cranked torsion bars 4 full turns.
Attachments
12 VDC mini hack saw
12 VDC mini hack saw
Post Reply